Fully automatic Long service life can juice filling machine packing line

Energy saving. High efficient. Adapt to customer factory layout - Special lubrication system, keep products clean, health, safety - Extended service life

1 Carbonation Mixer

General Introduction

QHS series beverage mixer has the reasonable structure, high precision mix, plenty CO2 mix. Mainly applies to all carbonated beverages mixed processing, and can also be used for other beverages. It is the main equipment in complete equipments of carbonated beverage manufacturing.

Main features

1) Advanced mass flow in-line blending and carbonation for reduced product & ingredient losses;

2) High efficiency deaeration

3) Simplified, user-friendly, operator interface

4) Automated “ no-dump” start-up capability

5) Complete product recipe management

6) Ingredient usage trending and totalling

7) Improved product yields and consistency

8) Reduced B.O.D. cost

9) Fast, favorable return-on-investment

Process

Water De-aeration Water Carbonation Proportioning of water and syrup Cooling System

2 Depalletizer

General Introduction

QHS series beverage mixer has the reasonable structure, high precision mix, plenty CO2 mix. Mainly applies to all carbonated beverages mixed processing, and can also be used for other beverages. It is the main equipment in complete equipments of carbonated beverage manufacturing.

Main features

1) Advanced mass flow in-line blending and carbonation for reduced product & ingredient losses;

2) High efficiency deaeration

3) Simplified, user-friendly, operator interface

4) Automated “ no-dump” start-up capability

5) Complete product recipe management

6) Ingredient usage trending and totalling

7) Improved product yields and consistency

8) Reduced B.O.D. cost

9) Fast, favorable return-on-investment

Process

Water De-aeration Water Carbonation Proportioning of water and syrup Cooling System

2 Depalletizer

3 Can Rinser

General description

It is used to clean empty can in canning production line. Empty cans will be sent to turning device first, which will be turned around then transferred into rinsing machine. Empty can will be running from top to bottom along the turning device. When empty cans enter into rinser, they will be cleaned by 80ºC hot water (provided by customer) to reach aseptic state of can. There is certain inclination angle in both sides of rinser, whose size could be adjusted properly when needed. Empty cans will be rolling in parallel way from top to end; the waste water will be discharged from outfall.

Technical parameters

4 Can Filler/Seamer Monoblock

Description

It is suitable for filling and seaming carbonated liquid such as cola, beer, functional beverage, etc. It is equipped the advanced device, electrical equipment, and pneumatic control technology. It has the characteristics of filling reposefully, high speed, liquid level control, seaming reliably, frequency conversion timing, less material loss. It is the preferred equipment for beverage plants.

Features

­ Wholly sealed widow structure which is beautiful, concise, easy and highly operated;

­ Product tank design with precision polishing inside;

­ High precision and large flow rate filling valves to meet productive requirement;

­ Specially designed roller structure which is easy to be adjusted, locked and ensure sealing function;

­ Friendly and convenient operating panel with high expansibility.

Working Procedure

Cans will be pushed into can holding platform one by one by feeding screw and star-wheel. Centering cup of filling valve will fall to can; the distance between filling valves and cans is sealed by springiness plastic ring. The movement of centering cup is generated by plastic idler wheel along curvilinear motion. After filled, valve will be closed and centering cup will rise from the can. Filled can will be sent to conveyor chain, then to seamer. Seamer will take lid, turn over the edge of can and turn the edge to finish the sealing action by the control of cam. After that can will be transferred to conveying system.

5 X-ray Level Detector

Description

Filling level detector is developed to meet international advanced level liquid level detection requirements. Use of low-energy X-ray after the interaction with the tested substances, materials-ray intensity with the test material surface changes the position of principle, to control the detection of liquid filling material capacity. Because of its non-contact measurement, a fundamental solution to the conventional weighing method cannot measure the liquid filling material on the production line capacity problems. It is widely used in food, pharmaceutical, chemical and other filling (either bottled or canned) liquid-line automatic control of the pipeline material. For ensuring product quality, increase economic efficiency and social significance.

Features

l Non-contact detection, speed and accuracy. Whether bottled, canned and other production lines could be detected on the surface of the filling.

l In line with a variable speed transmission state, free from transmission with rate stability limit.

l Stainless steel housing, sealed design and manufacture of the host, steam fog, water droplets, and environmental adaptability.

l Relative measurement method using free samples, free from temperature measurement resolution, long-term drift effects.

l Single-chip computer, the instrument anti-interference ability, high reliability.

l Sound, light alarm, and automatically remove the containers failed.

l Instrument set up inspection procedures and debugger, with the ability to automatically check for faults.

l Big touch screen display, LED backlit LCD, writing clear, bright, man-machine dialogue operation.

l Contain radioactive isotopes, radiation protection safe and reliable.

6 Air Blow Dryer

General description

The fast-blowing air from the blow of the high-pressure fan is sprayed out of an aperture, to remove the remaining waters from bottles to a high extent. The aperture is side-positioned to blow all sides of bottles with fast flowing air

Equipment makeup

l High-pressure fan

l Pressure equalizer box

l Air pipe

l Machine frame

l Control part

7 Date printer

Operations

• Message library (up to 100 messages)

•International operator/machine interface (choice of 31 languages)

• Large WYSIWYG backlit blue screen

• Integrated help for navigation and diagnostics

• Creation of logos directly on the operator/machine interface

• USB port

• M6’ ink circuit

• Jet Speed Control guarantees marking quality

• Automatic selection of fonts, depending on print speed and printhead/object distance

• Possibility to choose ink types: quick-drying MEK-free and MEK , alcohol-based, Colour changing for Sterilisation process

• 2 sealed intelligent cartridges, 0.8 litre each

• Quick connect/disconnect of accessories (photocell, encoder, alarm)

• RS-232 connectivity

Photos: Ginko

Printed in France on recycled paper - A48142 E1

Options

• One and two-dimensional barcodes (Datamatrix)

• Ethernet connectivity

• Printhead pressurisation kit (plant air required)

• Autonomous pressurisation kit (no plant air required)

• 3-metre umbilical

Accessories

• Printer supports: stands (stainless steel or aluminum), table or wall mounting bracket

• Stainless steel printhead cover

• Photocell

• Encoder

• Alarm beacon (24 V)

• Conveyor stop output

8 Automatic PE Film Shrink Wrapper

MB series machine has been designed for no tray, no cardboard case, packing with low cost in the operations, it is widely used in food, beverage, chemical and office industries

Technical Specification

­ Packing form: bottles and cans

­ Packing speed: 10 packs/min

­ Applicable container shape: circular container, quadrate container

­ Total power charge: 19kw three-phase-five-line 380v/50Hz

­ Machine size: L×W×H=6500×3200×2100mm(Include 1meter no-power rear roller frame)

­ Operating air pressure: 0.6~0.8Mpa

­ Air consumption: 0.4stere/min

­ Conveyor belt extreme breadth: 304mm

­ Conveyor height: according to client line (adjustable scope 150mm)

Main performance features

­ Compact & artistic shape. The frame is novel, unique.

­ Electronic induction feeding film, action is balanced and quickly replacing film.

­ Isothermal sealing cutter. The seal intensity is above cooling sealing cutter 3 times, the seal is even and the life is above cooling sealing cutter 80 times.

­ Transport system with speed regulation by frequency variation, the transmission action is precise and synchro.

­ The shrinkage chamber uses centrifugal thermal air circulation system, configuration is logical, heat insulation heat preservation, thermostat precision is high and the packing effect is better.

­ Disposition: SIEMENS, OMRON, UNIQUC, etc. advanced control component in the world, Well-equipped.

Grupos de Producto : Máquina de llenado de líquidos > Máquina de llenado de refrescos carbonatados